Creating A Mortise & Tenon Joint - Woodworking Joinery
The basic idea behind a mortise and tenon joint is that one piece of stock is inserted into the other, and then held in place with a fastener. ... Read Article
A-1 MORTISE And CROSSHOLE JIG M-100 OPERATING INSTRUCTIONS
COMPARE PAPER TEMPLATE SUPPLIED WITH MORTISE LOCK TO HOLE PATTERN If the mortise pocket is 4 ½" deep, set the stop collar so that there is 4 This will produce the correct depth. WEAR EYE PROTECTION WHEN DRILLING THE MORTISE POCKET HOLD DRILL SQUARE WITH DOOR and CLEAR CHIPS FREQUENTLY ... View Document
HANDLES & LOCKSETS TWO-POINT MORTISE LOCK ... - Truth Hardware
Adjusting a set screw in the matching keeper. Door Lock or Limiter can be added for applications requiring additional security 2. Bumper guards (Truth item number FIG. 5 TWO POINT MORTISE LOCK RECESSED FACEPLATE APPLICATION. 13f ... Get Doc
INSTRUCTIONS FOR HIT-45 MORTISE LOCK INSTALLATION
Base to the end of the router bit, this set up can now be Drill only on inside of door to mortise pocket only. Template hole size: 1/2”. (E) FOR LEVER SPINDLE HOLE FOR 8100 SERIES MORTISE LOCK WITH LE1, LE2, LE3, LE4, ... Return Doc
Installation Instructions For Stanley Omnilock 45HOM Mortise ...
Your 45HOM Mortise Lock. Topics covered include: Because these holes pass through the mortise pocket, it is recommended that each hole be drilled separately rather than straight through. of set screw Spindle Assembly on Outside door ... Fetch This Document
Door Hardware Lock Specifications
Exterior Mortise Lock Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 . and assures snug and solid fit in door mortise . Vital for Baldwin Mortise Locks . Steel Case:.875″ × 4″ × 5 .5″ (22 × 102 × 140mm) ... Retrieve Content
INSTRUCTION AND TEMPLATE FOR INSTALLING MORTISE LOCK RT - M1 ...
LINE UP WITH VERTICALLINE ON DOOR 1. Allen Key 2. Set Screw (2) 3. Left Hand Lever Handle (inside) 4. Spring Pack (inside) 5. Sub Mounts (inside) 6. MORTISE LOCK WITH 2 3/4” BACKSET PLEASE NOTE Springs are handed. Black must be facing you for Right Hand Lever. Redfor Left Hand Lever. ... Content Retrieval
Installation Instructions: Emtek Pocket Door Hardware
Install the Emtek Pocket Door latch and strike hardware using this three template set and special 7/8” will produce the finish mortise for the strike on the door jamb; ... View This Document
Heavy Duty Mortise Passage Pocket Door Lock - YouTube
The Emtek Heavy Duty Mortise Passage Pocket Door Lock set is used in situations when you want a door to just slide open and closed without the need to lock. ... View Video
Hang Slab Door - Install Slab Door - Home...
How to Install an Interior Slab Door. Using the old door as a guide, Trace the outline of the latch plate, then remove and set aside the latch mechanism. Use your chisel to cut along the outline of the latch strikeplate. ... Read Article
7800/8200 Mortise Locks SARGENT 8200 Series Mortise Lock ...
7800/8200 Mortise Locks SARGENT 8200 Series Mortise Lock Function List Multi-function Lockbody Options 04, 05, 06, 13, 31, 36, 37, 38 INSIDE and install security set screw (K) to plate assembly (F) with security torx Clean door pocket and verify hand of lock. 1. Slide lock body in door ... View Full Source
Sliding And Pocket Door Hardware Solutions For Applications
9100ADAL sliding door lock set 10-1. 2001ADAP sliding/pocket door sets Accurate’s 2001ADAP pocket/sliding door sets meet the “no pinch”, “no grasp” ADA the door must protrude a minimum of 4” to attach the ADA pocket door hardware For lock specifications, please refer to ... Read Content
Lock Preparation - Home Begins With The Door | Therma-Tru
Preparation shown is for Hoppe multipoint lock set door preparation DOOR PREP Apply Cross Mortise Fixture Set the cross mortise jig on the edge NOTE: Over tightening can cause the width of the mortise pocket to be cut improperly. NOTE: Be sure the jig is flat against the edge of the ... Fetch Content
Pocket Door Hardware: Pocket Door Hardware Keyed Locks
Min 5068 Max 6080 or 80610 Retrieve Content. Urban Sliding And Pocket Door Hardware - Accurate Lock #2002 sliding/pocket door locks: Content Retrieval. ... Read Article
ML2000 Mortise Locks I NC Ad: A SBLOY D 225 Episcopal Roa D
ML2000 Mortise Locks with MUSÈO Levers Installation Instructions MUSÈO Collection Sectional Trim Step 1 Mortise door pocket for lock assembly and bore holes, using template listed or door marker provided. Thread cylinder set screws partially into lock before inserting lock into mortise ... Document Retrieval
Sliding Glass Door Mortise Lock Sell Sheet - NuAir
Mortise Lock Available Pocket or Bypass up to 4 Tracks Tested to Dade 202 Protocol Tested to Dade 201, 202 and 203 Protocol KeepSafe™ Maximum Laminated Handle Set NuAir Sliding Glass Door Mortise Lock and Handle Set Assembly Windows and Doors ... Read More
Bit Key Mortise Lock - The Home Depot
Bit Key Mortise Lock A. Loosen set screw on one knob and unscre w knob from spindle (Fig. 1). B. Remove second knob Fand spindle from door (Fig. 1). C. Remove screws from faceplate of old lock and remove old mortise lock from door D. Place new mortise lock in existing door pocket ... Get Document
Baldwin Hardware Corporation - Scene7
Baldwin Hardware Corporation Mortise Lock Installation Instructions TOOLS REQUIRED the intended lock. Mortise the pocket in the door 1/8" deeper than the lock being installed. Start the set screw before sliding the knob or ... View This Document
Mortise Locks - Lock And Hinge
Pocket Door Hardware Material: brass 16 mm (5/8”) 14 mm (9/16”) 2 mm 28 mm (1 1/8”) (1/16”) 64 mm (2 1/2”) 82 mm (3 1/4”) 18 mm (11/16”) 160 mm (6 5/16”) Packing: 1 set Mortise Locks For Sliding Doors. Title: 1-16 Author: Wes Jones ... Access Document
Installation Instructions For 45H & 47H Mortise Locks
Installation Instructions for 45H & 47H Mortise Locks BEST ACCESS SYSTEMS template aligns with the mortise pocket prepared in the door. 3 Using the centerlines on the door edge template as a door with a CHB or RHB function mortise lock as a free-swinging door. ... Read Full Source
Passage Mortise Lock Set—Lever To Lever
Mortise Lock Instructions 1. Mark the Door The standard location of the mortise lock is determined by placing the center of the lever or knob at 36” above ... View Doc
No comments:
Post a Comment